Dual power industrial shunting

ZTYS1200 Dual Power Diesel Shunting Locomotive

A 2 × 600 hp diesel-hydraulic locomotive for controlled low-speed movements on industrial and dedicated railway networks.

VIEW TECHNICAL DATA

ZTYS1200 dual power diesel shunting locomotive operating in an industrial railway yard

Built for variable duty
Run one power group for lighter movements or both when the duty requires full installed output.

2 × 600 hpInstalled power

2430 tReference trailing load

60 mMinimum curve radius

15 km/hMaximum speed

Product introduction

Controlled power for industrial rail movements

The AGICO Group ZTYS1200 is a dual power diesel-hydraulic shunting locomotive for controlled movements on industrial and dedicated railway networks. It combines two KTA19-C600 diesel power units with hydraulic transmission in a B-B axle arrangement. Either power group can work independently, or both can operate together when the planned movement requires full output.

With 2 × 600 hp installed power, the locomotive is intended for assembling and breaking up wagon groups, positioning wagons at loading or unloading points, and transferring consists between plant areas. Its reference maximum trailing load is 2430 t on straight, level track. Gradient, curvature, adhesion, wagon resistance and braking arrangements all influence the permissible load.

The 15 km/h maximum speed keeps the design focused on low-speed industrial handling rather than main-line operation. A 60 m minimum curve radius and 15390 mm overall length support work in compact track layouts, subject to project-specific clearance and route checks.

AGICO Group ZTYS1200 dual power diesel-hydraulic shunting locomotive

Advantages and features

Designed around repeated shunting duty

01

Selectable dual power

Use one power group for lighter work or both groups when the operating plan requires full installed power.

02

Diesel hydraulic drive

Hydraulic transmission supports the repeated starts, reversals and controlled low-speed movements typical of yard work.

03

Compact track geometry

B-B running gear and a 60 m minimum curve radius support constrained industrial railway layouts.

04

Practical interfaces

JZ-7 locomotive braking, air brake, hand brake and a No. 13 top-operated coupler form the stated baseline.

Power and transmission

Two power groups one duty-based operating choice

Each six-cylinder KTA19-C600 engine is rated at 448 kW or 600 hp at 2100 rpm. The specified maximum torque is 2237 Nm at 1500 rpm, and the stated minimum fuel-consumption rate is 196 g/kWh. Actual fuel use varies with load, operating cycle, ambient conditions and equipment configuration.

The ZTY600 hydraulic torque converter has a 450 mm circulating diameter. Electro-hydraulic reversing provides forward, neutral and reverse positions, giving the driver a clear sequence for frequent yard movements.

  • 24 V DC electric starting
  • Two air compressors, each rated at 0.57 m³/min
  • Single- or twin-unit operating choice
ZTYS1200 twin KTA19-C600 diesel-hydraulic power arrangement

Technical parameters

ZTYS1200 locomotive specifications

ParameterSpecification
Installed power2 × 600 hp
Diesel engineKTA19-C600
TransmissionDiesel-hydraulic
Reference maximum trailing load2430 t on straight, level track
Maximum speed15 km/h
Minimum curve radius60 m
Track gauge / axle arrangement1435 mm / B-B
Wheelbase / bogie-center distance1800 mm / 5000 mm
Wheel diameter1050 mm
Service weightApproximately 85 t
Overall dimensions15390 × 3150 × 4410 mm
CouplerNo. 13 top-operated coupler
Coupler center height880 ± 10 mm
Brake equipmentJZ-7 locomotive brake; air brake and hand brake

The 2430 t trailing-load value applies to the stated straight and level reference condition. It must not be used as a guaranteed capacity for a route with gradients or tight curves. AGICO Group should review the ruling gradient, minimum curve radius, rail condition, expected adhesion, wagon resistance, braking method and operating cycle before project selection is finalized.

ZTYS1200 locomotive side and end outline showing B-B running gear and principal dimensions

Track and envelope

Verify the locomotive against the actual site

The B-B arrangement distributes the locomotive across two two-axle bogies. It uses a 1435 mm track gauge, 1800 mm wheelbase, 5000 mm bogie-center distance and 1050 mm wheel diameter. These dimensions are relevant when assessing workshop approaches, loading tracks, terminal ladders and other constrained industrial layouts.

The 15390 × 3150 × 4410 mm overall envelope must be checked against buildings, platforms, workshop equipment and local clearance requirements. The No. 13 top-operated coupler has a nominal center height of 880 ± 10 mm and should be reviewed against the buyer’s wagon fleet and coupling practice.

Application scenarios

Where the ZTYS1200 fits

01

Industrial plants and private sidings

Wagon positioning and transfer movements within steelworks, processing plants and manufacturing sites.

02

Ports and freight yards

Assembling wagon groups and moving loaded or empty vehicles between loading, unloading and interchange tracks.

03

Railway stations

Controlled shunting and transfer work where the route, braking practice and permissible load are confirmed.

04

Depots and workshops

Low-speed rolling-stock movements within maintenance bases, vehicle depots and dedicated engineering tracks.

Project selection guidance

Bring the duty data before choosing the configuration

Prepare the maximum trailing load for loaded and empty movements, the ruling gradient, tightest curve, route length, daily operating hours, number of starts and reversals, rail condition, ambient temperature range, wagon braking arrangement and coupler requirements. These inputs allow the ZTYS1200 baseline to be evaluated against real site resistance and braking needs.

Maximum loaded and empty trailing mass

Ruling gradient and tightest curve

Daily cycles and route length

Braking and coupler requirements

Rail condition and expected adhesion

Ambient operating environment

AGICO Group

Discuss your shunting duty with AGICO Group

Share your trailing load, gradient, curve radius, operating cycle, braking practice and coupling requirements. Contact AGICO Group for a project-based review of the ZTYS1200 dual power diesel shunting locomotive.

Scroll to Top